Home >
Questions and Answers >
Tracking Questions
How to setup PopAds on Voluum (13)
03-27-2017 01:53 PM
#1
tkyorahat (Member)
How to setup PopAds on Voluum
Hi guys,
Can someone please show screenshots of how to setup PopAds on Voluum? (e.g. what tokens you use)
03-27-2017 03:10 PM
#2
gunnar (Member)
Hi tkyorahat,
you can just use the popads template.
03-27-2017 03:20 PM
#3
tkyorahat (Member)
Thanks, where can I find it?
03-27-2017 09:23 PM
#4
vortex (Senior Moderator)


Then select popads and "Load Template".
Amy
03-28-2017 09:47 AM
#5
tkyorahat (Member)
Thanks, this is what I was looking for.
10-16-2017 05:08 PM
#6
craig88 (Member)
I didn't want to start a new thread, but I'm not sure how to do the postback to popads properly?
http://serve.popads.net/cpixel.php?s...xxxxxxxxxx&id=[IMPRESSIONID]&value={payout} Is what I had on FunnelFlux, but this doesn't seem to work on Voluum. Do I need to change [IMRESSIONID] to "impressionid" which is the parameter?
10-17-2017 02:32 PM
#7
vortex (Senior Moderator)

Originally Posted by
craig88
I didn't want to start a new thread, but I'm not sure how to do the postback to popads properly?
http://serve.popads.net/cpixel.php?s...xxxxxxxxxx&id=[IMPRESSIONID]&value={payout} Is what I had on FunnelFlux, but this doesn't seem to work on
Voluum. Do I need to change [IMRESSIONID] to "impressionid" which is the parameter?
Try this:
http://serve.popads.net/cpixel.php?s2s=1&aid=xxxxxxxxxxxxx&id={externalid} &value={payout}
Amy
10-20-2017 02:08 PM
#8
craig88 (Member)
Thanks Amy, I did try that/this: http://serve.popads.net/cpixel.php?s2s=1&aid=xxxxxxx&id={externalid}&value ={payout} but popads is still not registering any conversions. Not sure if there is anything else I might be doing wrong other than the postback which could cause the issue?
10-22-2017 02:51 PM
#9
vortex (Senior Moderator)

Originally Posted by
craig88
Thanks Amy, I did try that/this: http://serve.popads.net/cpixel.php?s2s=1&aid=xxxxxxx&id={externalid}&value ={payout} but popads is still not registering any conversions. Not sure if there is anything else I might be doing wrong other than the postback which could cause the issue?
Aside from this postback (from
Voluum to popads), there 2 other things that need to happen:
1)A conversion needs to have been made - this is obvious - and recorded at the aff network.
2)The conversion needs to have been posted back by the aff network to
Voluum.
Only after that, can the voluum-to-popads postback do its job. I haven't personally used this voluum-popads postback, so have no idea if it even works. Could you please contact popads support and see what they say?
Amy
10-22-2017 03:29 PM
#10
craig88 (Member)
Thanks, Voluum knows about the conversions so will give popads a shout and see if they know what the problem is.
10-23-2017 07:08 AM
#11
tuzbuz (Member)
Hello,
can I ask a question? landing page required? for popads. or direct site link?
10-23-2017 09:57 AM
#12
craig88 (Member)
Can do either. Popads is one of the most lenient TS's around
10-24-2017 02:13 AM
#13
vortex (Senior Moderator)

Originally Posted by
tuzbuz
Hello,
can I ask a question? landing page required? for popads. or direct site link?
The traffic source will not care whether you use a landing page or not - as long as either/both the landing page and/or the offer page are compliant with their TOS.
Some offer owners (aka advertisers) do have rules against direct-linking, so do read through the offer requirements carefully.
The main consideration for us affiliates though, is whether the offer CAN convert well without a lander. This will depend on how much pre-selling the offer will need. If it doesn't need much pre-selling, then you can direct-link. Otherwise, you'll need to use a lander. Also, some offers can convert when direct-linked, but can convert even better when a lander is used. It all depends on the particular offer, and how good your particular lander is.
Amy
Home >
Questions and Answers >
Tracking Questions